Instructions for the assembling:
The example of the instructions are given as the example of model SU- 30 , the other models do not differ from the shown ones.
Precautions: The kit contains small parts , you must not given the children under the age of 3.
Important: DO NOT USE LIQUID NAILS !
Choose adhesive not containing the following chemical compounds: organic solvents (acetone , acetic acid ethyl ester , the solvent inksturpentine);
Unacceptable use of sand - cement mortars intended for this material in construction.
When using do not forget about safety.
Use disposable gloves. Pay attention to respiratory protection and vision. The composition of adhesives may include toxic substances. Choose products proven manufacturer .
The kit comes as is.
Model length - 1440 mm ( + -5mm )
Recommended follow- weave model films , tape or fiberglass to impart rigidity and strength model. Do not forget that the weight
For proper assembly required :
3 . Rags to remove adhesive residue , removing stains.
7. Strongly recommend to make a set of shipments and stick them above pelt . Enough segment size 500x500 . The kit
Finishing produce finer sandpaper, grain selection at your discretion .
Also need a set of goods, used under gluing layers.
Allowed the use of acrylic ( NOT ALKYD !) Coatings on wood.
Assembly model should start with the preparation of the workplace and the necessary tools . Make sure you have enough free time.
1. Arrange items in the order they appear .
2 . Remove gloss polystyrene with all the details. Calculation model was made of a layer thickness 49.4 mm. , So do not overdo it. gloss
shoot up to 0.3mm . on each side ( enough to scratch ) . This is done for better adhesion layers when gluing.
3 . Conditional section details on 4-5 sites and start gluing.
4 . Fold the two adjacent layers . Note the error to be aligned with the gluing pins. Since heterogeneity
the material used , as well as the difference in mean lengths of projections of the layer thickness of the cut varies depending on the direction
of movement and velocity cutting the string. This deviation from the rules is not a marriage, AeroTetris continues to work on it.
5 . Brush evenly over the entire surface gluing , apply glue to both edges of the layers. The consistency , the adhesive should not resemble a
thick sour cream . It should not spread over the surface. If necessary, use an approved solvent adhesive. In this case , for Super PVAD3 such a solvent is water.
6. Connect the two parts together. Along the perimeter of the adhesive joint , leveling the surface with your fingers , tighten the pin so that the pin passes through
both layers angled .
After gluing, they are easily removed . The resulting item check on all sides, including internal grooves . If necessary, add
corrective pins . Remove excess glue with a cloth . Frozen drop of glue on the surface , will bring a lot of inconvenience when finishing .
Pay due attention to the duct . These pins are positioned easily with any material thickness of up to 2-3 mm. the thickness of the duct.
Place on a flat surface and attach the load.
7. Begin Bonding next couple of details in the previous paragraph .
Duct inlets cut yourself, based on the characteristics of the attachment.
8. Allow to dry glue. Patience. Pasting from one model AeroTetrisa goes up to 5 hours or more.
Please note , as gluing when needed to connect a pair of 2-3-4 parts , since the center of gravity , there is a weight not simply . You can use the strap .
When using the strap , be careful . Expanded polystyrene is quite soft material and excessive force can damage it, deform . In this case, use of waste material as washers . The factory set them enough.
When the model is glued together , start to finish. Conveniently display surface in the bathroom with warm water. If you used a waterproof PVA model debonding at the seams. If waterproof PVA is not found, go to step 1. If , to use glue containing organic solvents and model lost its shape , shriveled or disappeared , go to the order form new model. You already have a 10% discount on all subsequent acquisition of AeroTetris. If there is sufficient experience with the foam, it is possible to produce agglutination with it , but we do not recommend its use. Reasonable deviations from this manual possible. Quality gluing depends on you and your hands.